Tips to install Bonve homogenizer mixing pump - Bonvepumps.com

 How to remove and install the homogenizer mixing pump when pump ship to the destination port? Below are the tips to install Bonve high shear mixer.

1. Pump sent to area other than China will be packed in plywood case.

2. Users are advised to check the packing list, instruction manual, certificate of qualification, and other accessories attached after opening the wooden case.

3. Pump can be delivered to the installation site when the sealing bags at the inlet and outlet remain intact.

4. In hoisting, the hoist links at the pump body and the motor are available for use. If possible, users is better to carry the pumps with forklift trucks, handle with care.

5.The foundation of pump installation should have a horizontal plane. In line with the installation dimensions, four basic holes should be scooped first. Then ground screws are to be put into the holes for cement casting. When the cement is dry, use sizing block to adjust the chassis and make it horizontal. Lastly, screw up the ground bolts.



6. Pipe linking the pump should have supports respectively, which should not be the pump body.

7. To avoid damage to the pump's motor, install an overload current protection device during installation.

8. When the pump is installed, there should be a filter set ahead of the pump inlet. The filter screen should be 20 meshes or greater.

9. In installation, at pump inlet should be fixed a gauge valve for convenience of damaged meters replacement.

10. After the pump is installed, mark the ground connection point at the motor and make it connect the earth in accordance with the national safety standard.

11. If the pump is mobile type, hose should be used as at the inlet and outlet of the pump. In this case, valve and manometer are not necessary. The pump can only be pulled on level ground as four wheels (two of them are wheels) are fixed below the base plate. In case of too steep slope or a sharp turn, particular care should be taken to prevent any off-balance or sliding.


Click to view tips on installing Bonve rotary lobe pumps


评论

发表评论

此博客中的热门博文

Lobe pump specifications | Rotary Lobe Pump Manufacturer

图片
  Bonve  is the leading manufacturer of  rotary lobe pumps  in China since 2001. We produce the pumps from 1inch to 16inch, the motors coming are from 0.75kW to 200Kw and the flow is upto 400m3/H. Bonve is the one who makes the biggest of  stainless steel lobe pumps .  Below is the main specifictions and guideline for the model selection.  We offer the  lobe pumps  covering all the sectors to transfer liquid products with various density and various viscosity. Contact us to learn more! Lobe pump specifications Model Displacement RPM Normal Flow Dis.Pre. Power Port size (mm) (L/r) (r/min) (m³/h) (Mpa) (kW) Stand. Enlarged 25BV12-05 0.06 10-1000 0-0.5 0-1.2 0.37-1.1 15 25 40BV12-2 0.15 10-1000 0-2 0-1.2 0.75-2.2 25 40 50BV12-5 0.32 10-800 0-5 0-1.2 1.5-4 40 50 65BV12-10 0.65 10-600 0-10 0-1.2 2.2-7.5 50 65 80BV12-20 1.74 10-500 0-20 0-1.2 4-15 65 80 90BV12-30 2.60 10-500 0-30 0-1.2 5.5-22 80 100 100BV12-40 3.65 10-500 0-40 0-1.2 7.5-30 80 100 125BV12-50 4.60 10-500 0-50 0-1.2 7.5-37 100
阅读全文

How to troubleshoot when the homogenizer mixing pump fails - bonvepumps.com

图片
  High shear homogenizing mixer   will inevitably encounter some failures during use. At this time, it is necessary to find out the cause of the   high shear homogenizing mixer   failure through troubleshooting, and then find out the countermeasures based on the cause of the failure. The following are some of the faults that may occur in the  high shear homogenizing mixer . You can check according to the use of the  high shear homogenizing mixer . When the pump does not discharge or less capacity 1. Check whether the valve at inlet and outlet pipe open. 2. Whether the pipeline setting of the  high shear homogenizing mixer  is too complicated. 3. Whether the inlet and outlet pipelines of the pump are blocked. 4. The concentration and viscosity of the processed product will reduce the production efficiency of the  high shear homogenizing mixer  or not discharge the product. Solution: Add a feeding pump to the feed port of the mixer or dilute the product before entering the feed port of t
阅读全文

Rotary lobe pump applications and advantages - Bonvepumps.com

图片
  Rotary lobe pumps types Applications of rotary lobe pumps Advantages of rotary lobe pumps Types of rotary lobe pumps Rotary Lobe pump manufacturers  mainly divide their pumps into two types, food sanitary grade lobe pumps and industrial chemical grade lobe pumps. Applications of lobe pumps Food sanitary grade lobe pumps  include, but limited to: Foods: Chocolate, concentrated milk, yogurt, honey, syrup, cane sugar, tomato juice, concentrated juice, jam, ice cream, milk, yeast slurry, meat slurry, jelly, condiment, lees, soybean protein, flour slurry, etc. Pharmaceuticals: Ointments, extract, medicine latex, pill paste, syrup, health care products, drugs,vaccine etc. Industrial chemical grade lobe pumps  include, but are not limited to: Consumer chemicals: AES, LAS, AOS, K12, glycerol, fatty alcohol, bathing shampoo, skin cream, shampoo, detergent liquid, toothpaste soap, washing powder slurry, etc. Refined chemicals: Dyes stuffs, pigments, all kinds of pulp, chemical additives, adhes
阅读全文